Skip to Content

  Help Center -> Loggers -> Flex Logger -> Using the EXACT Device Manager App

Using the EXACT Device Manager App

Connect to a Flex logger over Bluetooth, then change its mode or how often it sends readings.

Updated Nov 17, 2026

The EXACT Device Manager app connects your phone to an EXACT Flex logger over Bluetooth. Use it on site to check a logger's battery and firmware, and to change two of its settings:

  • Mode: how the logger sends its readings to the Portal.
  • Transmission interval: how often it sends them.

Before you begin

  • An iPhone or Android phone with Bluetooth turned on
  • The EXACT Device Manager app, installed from the App Store or Google Play
  • An EXACT Device Manager account. EXACT Support creates it and sends you the email address and password to sign in with.
  • A magnet, such as the EXACT Flex Magnet Keychain
  • Access to the logger, so you can swipe the magnet across it

In the screenshots, numbered marks show where to tap.

Connect to a logger

A magnet swipe wakes the logger so the app can find it. You then connect to it from the app's list of available devices.

Sign in

If the app opens on its sign-in screen, sign in with the email address and password EXACT sent you.

The app's sign-in screen, titled BLE Device Manager. Numbers match the steps below.
The app's sign-in screen, titled BLE Device Manager. Numbers match the steps below.
  1. Enter your email address in Email Address.

  2. Enter your password in Password.

  3. Tap Sign In.

Find the logger and connect

Swipe the magnet right before you tap Scan, so the logger is awake while the app looks for it.

The serial number label on a Flex logger. Numbers match the steps below.
The serial number label on a Flex logger. Numbers match the steps below.
The scanner, ready to scan.
The scanner, ready to scan.
  1. Swipe the magnet along the logger's serial number label in a single pass, without stopping on it. The logger's status LED starts flashing to show it's awake.

  2. Tap Scan right away. The button reads Scanning while the app looks for loggers nearby.

    The logger found under Available Devices. Numbers match the steps below.
    The logger found under Available Devices. Numbers match the steps below.
  3. Find your logger under Available Devices. Each logger is listed as Flex_ followed by its serial number, such as Flex_10001027.

  4. Tap Connect next to your logger.

Done. The logger's page opens and shows Connected under the logger's name.

What the logger's page shows

The logger's details at the top of its page: battery, versions and current settings.
The logger's details at the top of its page: battery, versions and current settings.

Battery

The logger's battery charge, shown next to its name.

Hardware Version

The logger's hardware revision.

Firmware Version

The firmware the logger is running.

Configuration

The logger's current mode, shown with that mode's icon.

TX Interval

How often the logger sends its readings.

Change the logger's mode

The mode sets how the logger sends its readings to the Portal. Choose the one that suits where the logger is installed.

Choose a mode

LTE
Cellular Modem

Sends readings over the logger's own cellular connection. Use it wherever the logger has cell coverage.

LORA
Long Range

Sends readings by radio to an EXACT Relay, which passes them on to the Portal. Use it where cell coverage is poor but a working Relay is within 300 m (1,000 ft).

BLE
Direct Link

Sends nothing on its own. Readings reach the Portal only when someone downloads them from the logger over Bluetooth. Use it only if EXACT Support recommends it.

Relay
Gateway Router

Used by EXACT Relays, which collect readings from nearby LoRa loggers and send them to the Portal. Don't select it for a logger.

Warning

  • Switch a logger to LORA only if a working Relay is within 300 m (1,000 ft) of it. Without one, the logger can't reach the Portal and shows offline.
  • Don't change a Relay's mode unless EXACT Support asks you to. While it's in another mode, every LoRa logger that sends readings through it shows offline.

Switch the mode

This logger is in LoRa mode. Tapping LTE switches it to LTE. Numbers match the steps below.
This logger is in LoRa mode. Tapping LTE switches it to LTE. Numbers match the steps below.
  1. Under Select Device Mode, tap the mode you want.

    After tapping LTE, the LTE tile has a check mark and Configuration shows LTE.
    After tapping LTE, the LTE tile has a check mark and Configuration shows LTE.

Done. The mode you tapped shows a check mark, and the Configuration tile at the top of the page shows the new mode.

Change the transmission interval

The transmission interval sets how often the logger sends its readings. It doesn't change how often the logger records them. Sending more often gets new readings to the Portal sooner, but runs the battery down faster.

Choose an interval

5 min (High Frequency)

Sends every 5 minutes. New readings reach the Portal soonest, and the battery runs down fastest.

15 min (Standard)

Sends every 15 minutes, balancing timely readings and battery life.

1 hr (Power Saver)

Sends every hour, for the longest battery life.

Set the interval

The Transmission Interval section, with 15 min active.
The Transmission Interval section, with 15 min active.
  1. Under Transmission Interval, tap the interval you want.

Done. The interval you tapped shows ACTIVE, and the TX Interval tile at the top of the page shows the new interval.

Disconnect

  1. When you've finished, tap the X in the top-right corner of the logger's page to disconnect.

Troubleshooting

The app says No devices found, or my logger isn't in the list

The logger isn't awake, or it's out of range. Stand next to the logger, swipe the magnet along the serial number label again, check that the status LED flashes, and tap Scan right away.

The status LED flashed purple when I swiped the magnet

The magnet stayed on the label too long. Holding it there for about 10 seconds restarts the logger. A restart doesn't erase any readings. Once the logger has restarted, swipe the magnet in a single pass and tap Scan right away.

The status LED doesn't flash when I swipe the magnet

Swipe again along the whole serial number label. If the LED still doesn't flash, the battery may be flat. Charge the logger (see Charging Your Flex Logger), then try again.

The app never finds any logger

Check that Bluetooth is on, and that you allowed the permissions the app asked for when you first opened it. You can review them in your phone's settings for the EXACT Device Manager app.

More than one logger is in the list

Connect to the one whose name ends in your logger's serial number. The logger nearest you usually has the strongest signal, the dBm value closest to zero: -54 dBm is stronger than -85 dBm.

I can't sign in

Enter your email address and password exactly as EXACT sent them. Passwords are case-sensitive. If you've forgotten yours, tap Forgot Password? on the sign-in screen. If you don't have an account, contact EXACT Support.

The app lost its connection to the logger

You may have moved out of Bluetooth range, or the logger went back to sleep. Stand next to the logger, swipe the magnet again, tap Scan right away, and reconnect.

The interval I tapped doesn't show ACTIVE

Tap Refresh next to Transmission Interval to read the setting from the logger again. If it still shows the old interval, disconnect, swipe the magnet, reconnect and try again.

My logger shows offline in the Portal since I switched it to LoRa

It can't reach a working Relay. Check in the Portal that the Relay is online and within 300 m (1,000 ft) of the logger. If no Relay is in range, switch the logger back to LTE. For more checks, see My Flex Logger is Offline.

Getting help

Contact EXACT Technology support with the logger's serial number, the setting you were changing, and a screenshot of the app.